@Tiompan.

tiompan wrote:
harestonesdown wrote:
tiompan wrote:
harestonesdown wrote:
[quote="tiompan"]I can't find the stone circle marked on the large scale map .
Could you give me the co-ordinates for it from GE ?

Is the stone at the site you "arrowed " on GE ?

I'm using windows 10. I can't get GE to work on it!

Tha's a nuisance . Works fine in mine .


From my notes i put the circle at SK26940 86200 - ish.
Stu marked the stone at centre pic at SK26900 86300 - ish

Looking at the your arrowed pic for the stone it's 21m to the NE of what looks like a 6 figure grid ref so I've gone for the visual which comes out at SK 26884 86310 .
Assuming the stone circle ref is fine then the arrowed stone -stone circle alignment is a long way off any point where the sun would be seen on the horizon ,i.e. when the sun would be seen at that alignment it would be quite high . Taking the original 6 figure ref for the stone would be worse i.e. the sun would be even higher and never seen to rise at that bearing on the horizon .
The same applies to the moon at the major standstill , with the 10 figure being closest but but still off by about 5 degrees .
It would be good to get the exact refs to be more accurate but even with the rough ones it looks very unlikely .

Thanks for taking the time to look for me George.
Next time up there i'll take 10 fig grid references. Don't know why i didn't when i was there Monday. Doh!
No problem , I enjoy doing it .

Pics from GE (when you get it working ) marking the spots ,or co-ordiinates are good too .

I've given up hope with GE on W10.
Tried multiple installs, cleared all trace of it from the registry etc, re-installed. No joy. It's a pita. :/

harestonesdown wrote:
tiompan wrote:
harestonesdown wrote:
tiompan wrote:
[quote="harestonesdown"][quote="tiompan"]I can't find the stone circle marked on the large scale map .
Could you give me the co-ordinates for it from GE ?

Is the stone at the site you "arrowed " on GE ?

I'm using windows 10. I can't get GE to work on it!

Tha's a nuisance . Works fine in mine .


From my notes i put the circle at SK26940 86200 - ish.
Stu marked the stone at centre pic at SK26900 86300 - ish

Looking at the your arrowed pic for the stone it's 21m to the NE of what looks like a 6 figure grid ref so I've gone for the visual which comes out at SK 26884 86310 .
Assuming the stone circle ref is fine then the arrowed stone -stone circle alignment is a long way off any point where the sun would be seen on the horizon ,i.e. when the sun would be seen at that alignment it would be quite high . Taking the original 6 figure ref for the stone would be worse i.e. the sun would be even higher and never seen to rise at that bearing on the horizon .
The same applies to the moon at the major standstill , with the 10 figure being closest but but still off by about 5 degrees .
It would be good to get the exact refs to be more accurate but even with the rough ones it looks very unlikely .

Thanks for taking the time to look for me George.
Next time up there i'll take 10 fig grid references. Don't know why i didn't when i was there Monday. Doh!
No problem , I enjoy doing it .

Pics from GE (when you get it working ) marking the spots ,or co-ordiinates are good too .

I've given up hope with GE on W10.
Tried multiple installs, cleared all trace of it from the registry etc, re-installed. No joy. It's a pita. :/[/

Is it GE Pro ?

harestonesdown wrote:
tiompan wrote:
harestonesdown wrote:
tiompan wrote:
harestonesdown wrote:
[quote="tiompan"]I can't find the stone circle marked on the large scale map .
Could you give me the co-ordinates for it from GE ?

Is the stone at the site you "arrowed " on GE ?

I'm using windows 10. I can't get GE to work on it!

Tha's a nuisance . Works fine in mine .


From my notes i put the circle at SK26940 86200 - ish.
Stu marked the stone at centre pic at SK26900 86300 - ish

Looking at the your arrowed pic for the stone it's 21m to the NE of what looks like a 6 figure grid ref so I've gone for the visual which comes out at SK 26884 86310 .
Assuming the stone circle ref is fine then the arrowed stone -stone circle alignment is a long way off any point where the sun would be seen on the horizon ,i.e. when the sun would be seen at that alignment it would be quite high . Taking the original 6 figure ref for the stone would be worse i.e. the sun would be even higher and never seen to rise at that bearing on the horizon .
The same applies to the moon at the major standstill , with the 10 figure being closest but but still off by about 5 degrees .
It would be good to get the exact refs to be more accurate but even with the rough ones it looks very unlikely .

Thanks for taking the time to look for me George.
Next time up there i'll take 10 fig grid references. Don't know why i didn't when i was there Monday. Doh!
No problem , I enjoy doing it .

Pics from GE (when you get it working ) marking the spots ,or co-ordiinates are good too .

I've given up hope with GE on W10.
Tried multiple installs, cleared all trace of it from the registry etc, re-installed. No joy. It's a pita. :/
Loaded up W10 a few days back and GE Pro works fine, my printer was kicked into touch though until I upgraded the driver.

Here's the Pro download Geoff
http://www.google.com/earth/download/gep/agree.html